Bộ mũ và găng tay đan cải

Dành cho cô nàng chăm chỉ của anh chàng lười biếng 😛

Mũ này:

Găng này:

Trong mẫu này phần đan cải li ti và sát mũi nhau nên bạn có thể học cách cầm len như thế này cho tiện cải màu len, tất nhiên bạn dùng theo cách thông thường đã quen rồi cũng không sao (trong video hướng dẫn đan cải màu ở bài trước):

Công thức đan mũ:

PATTERN:
See diagrams M.1 and M.2 – diagrams are worked in stocking st.
——————————————————–
——————————————————–

HAT:
Worked in the round on circular needle and then on double pointed needles.
Cast on 128 sts on circular needle size 2.5 mm with off white.
Work rib = K 2/P 2 for 3 cm. Switch to circular needle size 3.5 mm. K 1 round while at the same time dec 8 sts evenly = 120 sts. Then work diagram M.1, then diagram M.2. REMEMBER THE KNITTING TENSION!
When diagram M.2 has been worked, there are 32 sts on needle and piece measures approx. 23 cm vertically. Work with off white until finished. First work 1 round as follows: * K 2, K 2 tog *, repeat from *-* the entire round = 24 sts. On next round, K all sts tog 2 by 2 = 12 sts. Cut the thread and pull it through the remaining sts, tighten tog and fasten.
The hat measures approx. 24 cm vertically.

---

Explanation to pattern diagram

	=	off white
	=	dark brown mix
	=	beige brown
	=	K 2 tog

Diagram

Công thức đan găng tay: có phần lưu ý khi đan găng này cho nữ đấy

Nếu chưa đan găng tay bao giờ, bạn hãy xem video sau cho dễ hình dung:

PATTERN:
See diagrams M.1, M.2 and M.3 for women’s mitten.
See diagrams M.4 and M.5 for men’s mitten.
——————————————————–

LEFT MITTEN:
Worked in the round on double pointed needles.

WOMEN: Cast on 96 sts on double pointed needles size 2.5 mm with off white. Work diagram M.1 over all sts, after diagram M.1 there are 48 sts on needle. Then work rib with K over K and P over P until piece measures 10 cm. Switch to double pointed needles size 3.5 mm – NOW MEASURE PIECE FROM HERE! Work 1 round in stocking st while at the same time dec 4 sts evenly = 44 sts. Continue with diagram M.2.

MEN: Cast on 56 sts on double pointed needles size 2.5 mm with off white. Work rib = K 2/P 2 for 10 cm.
Switch to double pointed needles size 3.5 mm – NOW MEASURE PIECE FROM HERE! Work 1 round in stocking st while at the same time dec 4 sts evenly = 52 sts. Continue with diagram M.4.

WOMEN and MEN:
When it has been worked up to the 3 black squares in the diagram, work diagram M.3 women and diagram M.5 for men over these 3 squares. Inc in diagram M.3/M.5 with 1 YO inside 1 st in each side, on next round K YO twisted (i.e. work in back loop of st) to avoid holes. When 4-5 inc has been worked (11-13 sts in thumb gusset), work 6-4 rounds without inc, then slip the 11-13 thumb sts on a stitch holder. Cast on 3 new sts behind sts on stitch holder = 44-52 sts. Then work diagram M.2/M.4. When beg to dec at top of hand, dec on each side of off white st in each side by working 2 sts tog with brown. Dec as follows before the off white st: K 2 tog. Dec as follows after the off white st: Slip 1 st as if to K, K 1, psso. After all dec, 12 sts remain on needle, cut the threads, pull them through remaining sts and tighten tog.

THUMB:
Slip the 11-13 thumb sts back on double pointed needles size 3.5 mm. Knit up 7-9 sts behind thumb = 18-22 sts. Continue in the round with diagram M.3/M.5. Dec on each side of the brown st in each side by working 2 sts tog with off white. Dec as follows before the brown st: K 2 tog. Dec as follows after the brown st: Slip 1 st as if to K, K 1, psso. After all dec, 6 sts remain on needle, cut the threads, pull them through remaining sts and tighten tog.

RIGHT MITTEN:
Cast on and work as left mitten but reversed, i.e. the 3 black sts for thumb are worked in 4th, 5th and 6th st from the right in the diagram.